A Step-by-Step Overview to Installing a Bathtub
A Step-by-Step Overview to Installing a Bathtub
Blog Article
How do you actually feel when it comes to Installing A Bathtub?
Setting up a bath tub isn't exactly brain surgery, yet it does require solid plumbing, woodworking, and often, tiling skills. Replacing an old tub with a brand-new one is additionally a moderately challenging job. If the old bathtub is conveniently accessible, the project can move rapidly; if you need to open up a wall to eliminate the old bathtub and position the new tub, the job is much harder. In either case, the job is within a residence handyman's skills, although you will require an assistant to move out the old tub as well as embeded in the brand-new one. Make sure you have actually certified yourself for the task as well as fit attempting it. Rather than employing a service provider to take control of a halfway-completed project, it is much better to think about utilizing one prior to you start. Opportunities are you may need an expert plumber to make tube connections.
This post will certainly aid you install a new bathtub in your shower room if you have actually currently acquired a brand-new tub and also do not require to alter the plan of your previous water supply pipes.
Your tools and product list must consist of the following:
Planning for the Installment
To start with, the sustaining structure provided with the bathroom needs to be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is very important to make certain that if the tap includes a plastic washer, it is fitted between the bath and the faucets. On a plastic bathroom, it is additionally practical to fit a supporting plate under the taps unit to prevent strain on the bathtub.
Fit the adaptable faucet adapters to the bottom of the two taps using 2 nuts and olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make sure you make use of every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom must now prepare to be suited its final position.
Removing Old Touches
If you require to replace old faucets with new ones as a part of your installation, after that the first thing you ought to do is disconnect the water. After doing so, switch on the faucets to drain pipes any water continuing to be in the system. The process of removing the existing taps can be fairly problematic as a result of the restricted gain access to that is frequently the instance.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the taps. Have a towel prepared for the continuing to be water that will originate from the pipes. As soon as the supply pipes have actually been eliminated, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming throughout this process. As soon as the taps have actually been removed, the holes in the bath/basin will certainly have to be cleaned of any type of old securing compound.
Before going on to fit the new faucets, compare the pipe links on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Setting up the Bath tub
Making use of the two wooden boards under its feet, put the bath tub in the needed placement. The wooden boards are practical in evenly spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto four tiny factors.
The next objective is to make certain that the bathtub is leveled all round. This can be accomplished by examining the spirit level as well as changing the feet on the bath tub until the spirit level reviews degree.
To install taps, fit all-time low of the outermost flexible tap port to the ideal supply pipeline by making a compression join; then do the exact same for the various other faucet.
Switch on the supply of water as well as inspect all joints as well as brand-new pipework for leakages and also tighten them if essential. Load the bath tub as well as additionally examine the overflow electrical outlet and also the regular electrical outlet for leaks.
Lastly, take care of the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and sealing around the tub must wait up until the bath tub has actually been made use of at least once as this will settle it into its final position.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic port to avoid damage to the thread. One end of the port fits on the plastic tail of the tap as well as the other end offers a connection to the existing supply pipes.
If you need to fit a monobloc, then you will require decreasing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the faucet in the placing opening in the bath/basin making certain that the washing machines remain in location between the tap and the sink. Secure the tap in position with the supplier given backnut. As soon as the faucet is safely in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal tap adapters. The previous kind ought to be connected to the tap finishes initially, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bath meets the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the installation can move enough to fracture a stiff seal, causing the water to penetrate the wall surface between the bath and also the tiling, causing problems with dampness and also possible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your fixtures as well as fittings. They are marketed in tubes as well as cartridges, and can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger space to load, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always fill the tub with water before securing, to allow for the motion experienced when the tub remains in use. The sealant can break rather early if you do not take into account this motion before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also quickly readily available on the market. It is a good idea to fit the floor tiles utilizing waterproof or waterproof glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a passionate reader about A Step-by-Step Guide to Installing a Bathtub, I imagined sharing that excerpt was valuable. Appreciated our entry? Please share it. Let someone else discover it. We take joy in reading our article about Tools You Need to Install a New Bathtub .
Click Here!
Report this page